You are purchasing a downloadable pdf of this Standard. This specification defines the requirements for selecting and evaluating mineral and slag abrasives . 6 Feb JETMAG® abrasive was analyzed in accordance with the required qualification tests of. SSPC-AB 1 for specific gravity, hardness, weight. 15 Feb Mineral and Slag Abrasives (Abrasive Specification No. 1).
|Published (Last):||2 May 2017|
|PDF File Size:||3.61 Mb|
|ePub File Size:||14.50 Mb|
|Price:||Free* [*Free Regsitration Required]|
There are many factors that impact quality and productivity during abrasive blast ss;c operations, but the abrasive quality is critical for long-term performance of the applied coating system.
The Importance of Monitoring Abrasive CleanlinessKTA University
It was removed from the test method in a revision as it does create confusion as you mentioned. If dust settles on the surface or water sspc ab 1 cloudy, the overall cleanliness of the abrasive should be questioned as this could cause impede production.
The cleanliness of the abrasive whether new or recycled is equally important. March 3, at June 16, at 7: This of course does not exclude regular inspection during actual sspc ab 1.
I do not think anyone can confidently quantify abrasive contamination transfer to a surface during abrasive blast cleaning, as there are too many variables to consider. The following is from the author, John Todd: Abrasive blast cleaning is the most common and productive sspc ab 1 of surface preparation. Water soluble contaminants are the non-visible soluble salts that may be present on an abrasive.
More importantly, it does not reveal the current condition of the abrasive. This includes personalizing content and advertising.
SSPC-AB 1, Mineral and Slag Abrasives
That is, abrasive cleanliness is an indirect requirement. This could cause widespread failures and become very expensive to repair. This is especially true for coatings in a marine service environment or immersion, such as ballast tanks. Proper surface preparation is one of the most critical steps towards maximizing the life of a coating system. If oil is sspc evident, the abrasive fails the test. The slurry is then poured through filter paper to prevent silt from fouling the probe and conductivity of the filtered extract is measured.
December 27, at 8: SSPC-AB 4 requires more frequent testing including at least three water-soluble xb tests at different times during an 8-hour period. This allows the contractor, inspector, and owner to identify any potential issues with the method before it becomes a larger, more costly wb. June sspc ab 1, at If coatings are applied to improperly prepared sspc ab 1, the sspc ab 1 is much more likely to fail prematurely.
SSPC-AB 2 requires additional field and laboratory tests for cleanliness to help ensure the abrasive recycling equipment is functioning properly and that the abrasive operating mix is still adequately sized. I agree that continued monitoring is highly recommended, especially with recyclable materials, since localized surface contaminants can become widespread when entered into the abrasive blasting media. By continuing to use our site, you accept our sspc ab 1 of cookies To learn more, click Read More to view our Privacy and Cookies Policy.
Selection of the type and size abrasive is dependent on sspc ab 1 degree of cleanliness specified, the depth of the surface profile, the type of substrate to be prepared, and any specification requirements regarding type e.
The Importance of Monitoring Abrasive Cleanliness
The container is shaken for about 1 minute and allowed to stand up to 5 minutes. December 29, at 5: Kaunteya, the following is a response from the author, John Todd: This test should be sspc ab 1 at least once per shift during blast cleaning operations and at least 3 tests per shipment sb bulk delivery.
Project specifications may not specifically address abrasive cleanliness. The note in the ASTM D test method was used as an example sspc ab 1 demonstrate that the higher the number, the more contaminated the abrasive.
This field test takes equal parts abrasive and deionized water mL of each that are combined and are twice stirred for 1-minute with an 8-minute standing time between stirs to leach any soluble salts from the abrasive. Oil transferred to the substrate can cause film defects e. Leave a Reply Cancel reply Your email address will not be published.
Abrasive selection is sspc ab 1 key component to an abrasive blast system. Transporting, storing, and recycling of the media can affect the cleanliness of the abrasive. There are several indirect requirements, including: The inspector shall ask the blasting team sspc ab 1 do blasting job on a test sspc ab 1 of a convenient bigger size and compare with standard panel.
AB 1, Mineral and Slag Abrasives
Tap water is added to the container xspc that it is approximately 1 inch above the abrasive. The sspc ab 1 blast cleaning standards are composed of both direct and indirect requirements. The degree of embedment from abrasive blast cleaning operations can vary widely even within a generic category of abrasive.
Your email address will not be published. Each standard has different requirements based on the type of media but sspc ab 1 ssc when it comes to the quality control tests for oil content and water-soluble contaminants. Surfaces contaminated with salt are much more likely to experience failures, such as blistering, than non-contaminated surfaces even at relatively low concentrations.
Water soluble salts transferred to the surface sspc ab 1 cause accelerated rust back, osmotic blistering, under-film corrosion, and premature coating failure. The surface of wb water is then visually examined for any oil droplets or sheen. Thank you for your question Mr.