Friends of PDF

all our visitors are our friends. we love them all. we want them to find and download pdf files from our website. we do our best to satisfy them. and they share our website on their facebook walls.




HT1621B DATASHEET PDF

HTB RAM Mapping 32×4 LCD Controller For I/o uc Features. Operating voltage: V~V Built-in kHz RC oscillator External kHz crystal or. Holtek HTB: available from 7 distributors. Explore Holtek on Octopart: the fastest source for datasheets, pricing, specs and availability. HT/HTG RAM Mapping 32´4 LCD Controller for I/O MCU PATENTED PAT No.: TW Features · Operating voltage: V~V · 32´4 LCD driver .

Author: Kigara Gardamuro
Country: Belarus
Language: English (Spanish)
Genre: Life
Published (Last): 20 April 2006
Pages: 22
PDF File Size: 3.18 Mb
ePub File Size: 2.75 Mb
ISBN: 246-1-87428-530-4
Downloads: 78886
Price: Free* [*Free Regsitration Required]
Uploader: Faur

Memory structure of the HT Calculation of the frequency is based on the system frequency sources as stated above. If an on-chip oscillator kHz or an external kHz frequency is chosen as the source of the system frequency, the frequency source is by default prescaled to 32kHz by a 3-stage prescaler. It is recommended that the host controller should initialize the HT after power on reset, for power on reset may fail, which in turn leads to the malfunctioning of the HT A generic LCD initialization sequence will consist of the th1621b steps: Yes Yes Yes Yes X: Finally, a class for a specific 7-seg LCD module that I found at bargains.

The system clock is used in a variety of tasks included LCD driving clock and tone frequency generation. Once the system is disabled or the tone output is inhibited, the BZ and the BZ outputs will remain at low level. In order to obtain the correct frequency, two additional load capacities C1, C2 are needed. The LCD screen will appear blank.

If successive commands have been issued, the command mode ID except for the first command, will h1t621b omitted. If the system clock comes from an external datwsheet source, the external clock source should daatsheet connected to the OSCI pad.

We provide procedures to software simulate the internal HT internal RAM and have transparent reading procedures. Only three or four lines are required for the interface between the host controller and the HT The value of the capacity depends on how accurate the crystal is.

HTB Datasheet pdf – RAM Mapping 324 LCD Controller for I/O MCU – Holtek Semiconductor

Data to be read or written or commands to be written have to be passed through the DATA line. Chip selection BZ, BZ: The LCD driving clock is derived from the system clock. We provide a very basic sketch for testing the main functions. Remark that we have. In the sequel we will describe each of these blocks. In this case, the system fails to enter the power down mode, similar to the case in the external kHz clock source operation.

The configuration of the time base generator along with the WDT are as shown.

HT1621B Datasheet

It is recommended that the host controller read in correct data during the interval between the rising edge and the next falling edge of the RD signal. The value of the driving clock is always Hz even when it is at a The clocked out data will appear on the DATA line.

The tone generator can output a pair of differential driving signals on the BZ and BZ, which are used to generate a single tone. In the next post we will provide a class for dealing with a generic 7-segments LCD module based on the HT chip with instruction set similar to the classical LiquidCrystal library here. These are stress ratings only. The configuration mode of the HT is called command mode, and its command mode ID is 1 0 0.

There are totally eight frequency sources available for the time base generator and the WDT clock. The HT contains a power down command to reduce power consumption. The 32kHz in the above equation indicates that the source of the system frequency is derived from a crystal oscillator of The crystal oscillator option can be applied to connect an external frequency source of 32kHz to the OSCI pin.

Adresses are organized as displayed in Figure 2.

If successive commands have been issued, the command mode Datashwet except for the first command will be omitted. If the VDD drops below the minimum voltage of operating voltage spec. Friday, February 6, HT If the CS pin is set to 1, the data and command issued between the ht1612b controller and the HT are first disabled and then initialized.

However, Holtek assumes no responsibility arising from the use of the specifications described.

The serial interface circuit is also reset. That is, after the external clock source is selected, the HT will continue working until system power fails or the external clock source is removed. If successive commands have been issued, the command mode ID, namely 1 0 0, can be omitted. For the most up-to-date information, please visit our web site at http: But if CS is at logic low level and is input to the CS pad, dstasheet data and ht1621 transmission between the host controller and the HT are all enabled.

HTB (HOLTEK) PDF技术资料下载 HTB 供应信息 IC Datasheet 数据表 (4/20 页)

We suggest that you can follow the table, which suggests the value of capacities. As this information may be updated at regular intervals users are reminded to consult the Holtek website http: The LCD corresponding commands are summarized in the table. The configuration of the system oscillator is as shown.

Employing both the time base generator and the WDT related commands, one should be careful since the time base generator and WDT share the same 8-stage counter. We have written a library to deal with all the features of HT The source of the clock may be from an on-chip RC oscillator kHza crystal oscillator The information appearing in this Data Sheet is believed to be accurate at the dahasheet of publication.

There are only two tone frequencies, namely: