Friends of PDF

all our visitors are our friends. we love them all. we want them to find and download pdf files from our website. we do our best to satisfy them. and they share our website on their facebook walls.




CONTACTLESS DIGITAL TACHOMETER PDF

Simple but accurate digital tachometer using microcontroller Has a resolution of 1 rev/sec. The tachometer use an optical pickup scheme for picking . Today, we are going to make a digital tachometer based on a PIC This tachometer can measure speeds up to RPM with the resolution . Sir, I want the code for the Contactless Digital Tachometer using PIC16FA. Abstract: This paper proposes a hardware design of an. “Digital Contact-less Tachometer” based on IR sensor for measuring the Revolutions Per Minute (RPM ).

Author: Arashiktilar Dazragore
Country: Anguilla
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 23 March 2010
Pages: 275
PDF File Size: 2.28 Mb
ePub File Size: 5.72 Mb
ISBN: 240-5-51694-628-1
Downloads: 29886
Price: Free* [*Free Regsitration Required]
Uploader: Zuluran

The program actually counts the number of negative going pulses in 1. Go through this article Delay using timer for a better grasp. Thank you for all.

How to make a contact-less digital tachometer using IR-light reflection technique – Embedded Lab

The circuit diagram of the LCD tachometer using is given below. You have to test and calibrate your sensors based on application. Any special interface cable? The circuit diagram of the digital tachometer is shown below. LCD tachometertachometer using This is for my study and teaching the program how to srite Thanks a lot for the Originators. Will be updated on this page. Dual supply opamps configured in single supply mode will not give results like a dedicated single supply opamp in the same situation.

For project purpose of measurement a distance below 1meter is suitable, but higher distances are possible if sensors are properly calibrated. The usage of LTH photo interrupter module makes it more rugged and stable. Every time the collector voltage of the photo transistor goes below 3.

Next part is the signal conditioning unit based on the opamp LM IC1. But this distance varies according to the climatic conditions in the region and also other devices operating in the area. In the crystal frequency is divided by 12 using an internal network before applying it as a clock for the timer.

For sending the light across directly max distance is about 10m or more with a very high sensitivity photo detector and high intensity IR LED. The working principle is almost similar to that of the previous version but the program is heavily modified.

What you use to program the ? From the above two graphs you can see that the negative going edge of the waveform indicates the passage of the reflective patch across the sensor and that means one revolution.

Embedded Lab

I have tested my T. We are working on the layout part! Leave a Reply Cancel reply Your email address will not be published. You may also like: Voltmeter using Transistor intercom circuit. For this setup and every other setup based on principle of reflection of comtactless the IR LED and the photo-sensor are placed side-by-side at a distance of mm from each other facing the obstruction contzctless is generally less than 10cm away from the tip of IR LED.

The instruction CPL A will just complement the digit drive pattern in accumulator so that it becomes suitable for the common anode display. Military uses high grade IR sensors that are able to operate for distances of few 10Km to Km. You can use any single supply opamp that matches our supply voltage 5V. I used LM just because that was the only single supply opamp with me at the time.

This is done just because to save my time but not a text book method. Hae there,i want to make the tracometer but a few things are troubling me. Digital tachometer using admin April 20, 39 Comments. The user interface for programming the microcontroller comes with the ISP module.

C remotes use IR sensors to operate. Your email address will not be published. Interfacing Nokia Display to Micro Controller Moisture sensing automatic plant watering system using Contactless digital tachometer using I want to ask whether the mechanism in this project counts the pulses for 60 seconds and then display it if so then how to configure to delay time for 60 sec and at the same time count the pulses in that duration?

The output is given in rpm revolutions per minute and the number of digits are increased from 3 to 5.

Digital tacchometer using Timer 1 is configured as an 8 bit auto reload counter for registering the number of incoming zero going pulses and Timer0 is configured as contacless 16 bit timer which generate the necessary 1 second time span for the Timer1 to count. You an use Keil to code, compile and test the program code. Heart rate monitor with sms alert. The job of this comparator unit is to convert the spiky collector wave form into a neat square pulse train so that it can be applied to the microcontroller.